Page 1Kit Product Number 128508Check out our website for more information on this and other exciting Model Tech products!HTTP://MODELTECH.GLOBALHOBBY
Page 10❑ Measure and draw a centerline mark on the top of the trailing edge of the stabilizer.❑ Extend the centerline mark across the top of the sta
Page 11❑ With the wing mounted to the fuselage and centered, measure the distance between the tips of the stabilizer and the tips of the wing. Pivot
Page 12❑ While holding the stabilizer in place, draw a line on each side of the stabilizer where it meets the top of the fuselage.❑ Pus
Page 13❑ Cut away the covering material from over the elevator servo mounting hole in the left side of the fuselage and from over the rudder servo mo
Page 14❑ Center the servo, then install the servo horn onto the servo, making sure that the servo horn is centered and pointing down toward the botto
Page 15❑ Thin C/A❑ # 1 Phillips Head Screwdriver❑ Needle Nose Pliers❑ Modeling Knife❑ Electric or Hand Drill❑ (2) 2-3/4" (70mm) Threaded W
Page 16❑ 5 Minute Epoxy❑ # 1 Phillips Head Screwdriver❑ Modeling Knife❑ Electric or Hand Drill❑ 1/16" (1.6mm) Drill Bit❑ Straight Edge Rule
Page 17❑ Cut away the covering material from over the landing gear mounting slot in the bottom of the fuselage.❑ Insert the 90º bend in each of the
Page 18❑ # 1 Phillips Head Screwdriver❑ Adjustable Wrench❑ Wire Cutters❑ Modeling Knife❑ Scissors❑ Electric or Hand Drill❑ (1) Hook and Loop M
Page 19❑ Using a clean cloth, wipe the airframe down completely to remove any dust, debris and oil. ❑ Cut out each of the decals and apply them usin
Page 2
Page 20● Check the operation of the throttle. Double-check that you're getting full power when the throttle control stick is at full.☞ If you&a
Page 21If you liked the Model Tech Apex 3D EP ARF, here's a few of the manyother Model Tech ARF airplanes that are currently available:Mini Magic
Page 22THIS PAGE INTENTIONALLY LEFT BLANK
Page 23Telling us what you like and don't like determines what model kits we make and how we make them. We would appreci
Page 24Fold along dotted lineFold along dotted lineGlobal Hobby DistributorsAttn: Global Services18480 Bandilier CircleFountain Valley CA 92728-8610
Page 3Global Hobby Distributors will not disclose the information it collects to outside parties. We do not sell, trade, or rent your personal inform
Page 4WARNINGS AND SAFETY PRECAUTIONS FOR ALL BRANDS OF LITHIUM POLYMER BATTERIESPlease read and understand the warnings listed in this section. Make
Page 5❑ 5 Minute Epoxy❑ Thin and Thick C/A❑ # 1 and # 2 Phillips Head Screwdrivers❑ 1.5mm Hex Wrench (Optional)❑ Adjustable Wrench❑ Wire Cutters
Page 6The covering material used on your airplane is real iron-on, heat-shrink covering material. It is possible with heat and humidity changes that
Page 7❑ # 2 Phillips Head Screwdriver❑ 1.5mm Hex Wrench (Optional)❑ Modeling Knife❑ Electric or Hand Drill❑ (1) Fuselage❑ (2) Motor Mount Stra
Page 8❑ Set the motor mounting straps and your motor back into place and realign them.❑ Place the remaining two motor mounting straps over the motor
Page 9❑ Cut away the covering material from within the outline you drew, then glue the wing hold-down doubler into place.❑ Cut away the covering mat
Comments to this Manuals